Hayward Pool Cleaner Not Moving: Troubleshooting Tips

Here’s why those areas are important:

The hose: A leaky hose means the cleaner isn’t getting enough suction to move. Air leaks can happen from a loose connection, a damaged section, or even a crack in the hose.
The diaphragm: The diaphragm is a rubber part inside the cleaner that helps regulate water flow. If it’s blocked or damaged, it can prevent the cleaner from moving correctly.

How to Check for Problems:

Hose Check: Visually inspect the hose for any obvious damage. If you see anything, replace that section of the hose. To check for leaks, you can submerge the hose in a bucket of water and watch for bubbles.
Diaphragm Check: You’ll need to consult your cleaner’s manual for instructions on how to access and inspect the diaphragm. If it’s dirty, try cleaning it. If it’s damaged, you’ll need to replace it.

Important Tip: Before you do any troubleshooting, make sure your pool pump is running and that the cleaner is properly connected to the pool’s suction system.

First, check the impeller. It could be clogged or jammed with debris. If you find debris, carefully clean it following the instructions in the maintenance section of your owner’s manual.

Next, inspect the brush roller and drive tracks. They may be stuck due to debris. If you find debris, clean it.

Finally, remember that your cleaner operates based on a combination of timing and pool wall detection. It will stop when either of these conditions is met.

Understanding the Hayward EVAC Cleaning Cycle:

Your Hayward EVAC cleaner relies on a sophisticated system to move around your pool and effectively clean it. Here’s a breakdown of how it works:

1. Timing: The cleaner runs for a set amount of time, usually determined by your pool’s size and cleaning needs. This is the default cleaning cycle.
2. Pool Wall Detection: The cleaner also has a built-in sensor that detects the pool wall. When it encounters the wall, it changes direction and continues cleaning. This ensures it covers the entire pool area.
3. Combined Action: The cleaner will stop when either the predetermined time limit is reached or when it detects the pool wall. This ensures efficient cleaning without unnecessary running time.

Troubleshooting Tips:

If your cleaner isn’t moving, it’s essential to understand the interplay of these two mechanisms. Here’s how to diagnose the issue:

Check the Timer: Ensure the timer is set to the correct time and that the cleaner is turned on.
Verify Wall Detection: Observe the cleaner’s movement. If it’s not changing direction or seems to be stuck in one spot, the wall detection sensor might be malfunctioning.
Examine the Impeller and Tracks: As mentioned earlier, debris can hinder the cleaner’s movement. Check the impeller for any obstructions and make sure the tracks are clear.
Consult Your Manual: Refer to your Hayward EVAC owner’s manual for specific troubleshooting steps and instructions.

Remember: It’s crucial to follow the manufacturer’s recommendations when cleaning and maintaining your pool cleaner. This ensures its proper operation and extends its lifespan.

First, check the hose. If it’s too short, your cleaner won’t be able to reach all corners of your pool. A simple solution is to buy an extension hose, and make sure it’s long enough to allow your cleaner to easily navigate the entire pool area.

The other common problem is the hose getting tangled or coiled. This can happen if your Kreepy Krauly isn’t stored properly after use. Try relaxing the hose before you put it away, and make sure it’s not getting caught on anything in its storage area. Sometimes, how you store your cleaner can impact how it moves through the pool.

Here’s a little more about Kreepy Krauly hoses:

The hose is the lifeline for your Kreepy Krauly, connecting it to the power source and allowing it to move around your pool. If the hose is too short, the cleaner simply won’t have enough reach to clean certain areas, especially if you have a larger pool. A longer hose gives your Kreepy Krauly more freedom to explore and clean every nook and cranny.

Think of your pool like a giant maze. If your Kreepy Krauly keeps getting stuck in the same spot, it’s likely the hose is too short, preventing it from reaching other areas. It’s like trying to navigate a maze with a string that’s too short to reach the exit!

By adding an extension hose, you’re essentially giving your Kreepy Krauly a longer leash to roam freely. It’s like letting your dog explore the park with a longer leash – they can cover more ground and have a more enjoyable time.

Once you release the buttons, you’ll see a message that indicates your cleaner is being reset. This process erases all the settings and programs on your cleaner, bringing it back to its factory defaults.

Think of it like giving your cleaner a fresh start! This is helpful when you’re having issues with your cleaner’s operation, or if you’ve made some changes to your pool setup (like adding a new feature or changing the pool’s shape) and need to start from scratch.

Important: Before you reset your cleaner, take a moment to consider if this is truly the solution you need. If you’re having trouble with your cleaner’s operation, sometimes the issue might be related to a blockage or a malfunctioning part. Check for these issues before resorting to a full reset.

After you reset your cleaner, you’ll need to program it again to your specific pool size and cleaning needs. Your owner’s manual will have all the details on how to program your cleaner.

Let me know if you need any other help with your Hayward pool cleaner!

Have you ever pulled your pool cleaner out of the water, only to find that it’s stuck? This usually happens because the hose has coiled up. Think of it like a rubber band; when you stretch it out, it remembers that shape. The same thing happens with your pool cleaner hose!

Here’s what likely happened:

You took the hose out of the pool and stored it. That’s a good habit to get into!
The hose coiled up while you were storing it. This is totally normal.
The water in your pool slowly reset the hose’s memory. The top layer of the water is actually pretty calm, unlike the water where your cleaner is working. The calm water helps the hose remember its coiled shape.

This makes it tough for your pool cleaner to get back to work. Think of it like this: the hose wants to stay coiled up, but the cleaner needs the hose to be straight to move properly.

How to Fix It:

The good news is that you can easily fix this! Just give the hose a good stretch. The best way to do this is to:

1. Lay the hose out flat on a clean surface. You can use your driveway or your lawn.
2. Slowly stretch the hose out to its full length. Don’t yank on it too hard!
3. Let the hose sit out in the sun for a few hours. This will help it “remember” its straightened shape.

Once the hose is nice and stretched, you’ll be able to put it back in the pool and your cleaner should be able to move around freely.

Additional Tips:

Don’t leave your hose out in the sun for too long. This can cause the hose to dry out and become brittle. A few hours should be enough.
Try to avoid coiling the hose too tightly when you store it. If you have to coil it, try to make the coils as loose as possible. This will help prevent it from getting stuck.
Consider using a hose reel to store your pool cleaner hose. A hose reel will keep the hose from getting tangled and help prevent it from coiling up.

By following these simple tips, you can keep your pool cleaner hose from getting stuck and ensure that your pool is always sparkling clean.

If your cleaner turns both ways, with a stop in between, put it on the pool floor and watch it closely. If it now turns in only one direction, there could be a problem with the Pod, A-frame, or turbine connection.

Here’s a closer look at why this happens:

The gearbox: This is the part that controls the direction of the cleaner’s movement. If the gearbox is worn out, it might not be able to switch directions smoothly. This will cause the cleaner to spin in circles or go back and forth in a jerky motion.
The Pod: This is the part that connects the cleaner to the pool wall. If the Pod is damaged or loose, it can cause the cleaner to spin in circles. The Pod has a small hole where water flows in and helps the cleaner run smoothly. If the hole is blocked, the cleaner won’t work properly.
The A-frame: This is the part that holds the cleaner’s wheels. If the A-frame is bent or damaged, it can cause the cleaner to spin in circles.
The turbine: This is the part that powers the cleaner. If the turbine is damaged or clogged, it can cause the cleaner to spin in circles or not move at all.

Checking for these problems:

1. Look for cracks, breaks, or signs of wear on the Pod, A-frame, and turbine.
2. Make sure the Pod is securely connected to the pool wall.
3. Clean the turbine to remove any debris.

If you’ve checked these things and your cleaner is still spinning in circles, it might be time to replace the gearbox. This is a relatively simple repair, but you may want to contact a qualified pool service technician to do the job.

Cleaner doesn’t move. – hayward.com

Learn why your Hayward suction cleaner may not move and how to fix it. Check the water flow, the shoes, the obstructions, and the drive train of the cleaner. hayward.com

Hayward Pool Vacuum Not Moving: How to Fix That?

Why is my Hayward pool cleaner not moving? There are a few reasons this could be happening. The first reason is that the suction from the skimmer is not strong enough to move the Hayward pool CleanerProfy

How to Repair or Analyze a Hayward Navigator Pool Cleaner that

DIY Home Repair and Improvement. 1.48K subscribers. 66K views 9 years ago. …more. Check out my updated video for hayward YouTube

Troubleshooting Hayward Navigator Pool Sweeper Not Moving

In this video I show you how to troubleshoot a hayward navigator that wont move YouTube

Hayward pool vac stuck going right or left or no movement

Hayward pool vac stuck going right or left or no movement. MBJ DIY. 10.3K subscribers. Subscribed. Like. 68K views 6 years ago #Kroger #Costco #Magnolia. Hayward pool YouTube

Hayward AquaNaut® Troubleshooting Guide

• Cleaner gets stuck in corners or hangs up on objects in the pool. • Cleaner is falling on its side (this can also be floats on leader hose missing). • Cleaner starts and stops. hayward.com

HAYWARD NAVIGATOR PRO TROUBLESHOOTING MANUAL

If the cleaner does not move, check the shoes for wear and the pool surface for algae (treat and remove) or remove the access cover and check for debris in the turbine area. Page ManualsLib

How To Repair a Hayward Navigator or Pool Vac Ultra Pool Cleaner

This guide shows you how to replace the common wear parts of a Hayward Navigator or Pool Vac Ultra Pool Cleaner. INYOPools.com

HAYWARD AQUANAUT TROUBLESHOOTING MANUAL Pdf

Page 10: Cleaner Does Not Move Cleaner Does Not Move • The pump may be turned off or on low speed. Make sure the pump is ON. • The three way valve may be in the wrong ManualsLib